Pressure and Hydrostatic Pressure
You push a thumbtack into a cork without any effort, but if you push on it with your flat finger, no matter how hard you press, nothing goes in. The force from your hand can be exactly the same in both cases. The only thing that changes is the area over which it is spread. That simple idea explains why knives cut, why skis don't sink, and why your ears hurt at the bottom of a pool.
What pressure is
Be clear about why the formula works: the total force doesn't tell you how much a push is "concentrated." Dividing by the area measures how much force falls on each square meter.
With the same force, the smaller the area, the greater the pressure.
In what unit is pressure measured in the International System of Units? Write its equivalence in units of force and surface area, and state after which scientist it is…
In what unit is pressure measured in the International System of Units? Write its equivalence in units of force and surface area, and state after which scientist it is named.
A crate of books pushes against the floor with a force of $200\ \text{N}$ distributed over a base of $0.5\ \text{m}^2$, as shown in the figure. Calculate the pressure it…
A crate of books pushes against the floor with a force of $200\ \text{N}$ distributed over a base of $0.5\ \text{m}^2$, as shown in the figure.
Calculate the pressure it exerts on the floor, in pascals, using $p = \frac{F}{S}$.
A workshop punch pushes against a metal sheet with a force of $20\ \text{N}$ and its tip has a surface area of $4\ \text{mm}^2$. a) Express the surface area of the tip…
A workshop punch pushes against a metal sheet with a force of $20\ \text{N}$ and its tip has a surface area of $4\ \text{mm}^2$.
- a) Express the surface area of the tip in $\text{m}^2$.
- b) Calculate the pressure exerted by the punch on the metal sheet.
Solving for each variable in the formula
The formula $p = F/S$ has three letters. With two pieces of data you can find the third:
The snow accumulated on a flat roof exerts a pressure of $600\ \text{Pa}$ over an area of $30\ \text{m}^2$. Calculate the total force supported by the roof.
The snow accumulated on a flat roof exerts a pressure of $600\ \text{Pa}$ over an area of $30\ \text{m}^2$. Calculate the total force supported by the roof.
To what depth must you descend in the water of a swimming pool for the pressure due to the water to be $49\,000\ \text{Pa}$? First rearrange for depth in the expression…
To what depth must you descend in the water of a swimming pool for the pressure due to the water to be $49\,000\ \text{Pa}$? First rearrange for depth in the expression $p = d\times g\times h$. Data: $d_{agua} = 1\,000\ \text{kg/m}^3$; take $g = 9.8\ \text{m/s}^2$.
A manufacturer wants to design a snowboard so that a $70\ \text{kg}$ person does not exert a pressure greater than $2\,000\ \text{Pa}$ on the snow. Take…
A manufacturer wants to design a snowboard so that a $70\ \text{kg}$ person does not exert a pressure greater than $2\,000\ \text{Pa}$ on the snow. Take $g = 10\ \text{m/s}^2$.
- a) Calculate the person's weight.
- b) What is the minimum surface area the snowboard must have so as not to exceed that pressure?
- c) If the snowboard is $1.75\ \text{m}$ long, what minimum width must it have? Express the result in centimeters.
The role of the contact area
A hiker walks through freshly fallen snow in boots and sinks up to her ankle; the next day she goes through the same place on skis and leaves hardly a footprint, as…
A hiker walks through freshly fallen snow in boots and sinks up to her ankle; the next day she goes through the same place on skis and leaves hardly a footprint, as shown in the figure.
If her weight is the same in both cases, explain using the concept of pressure why she does not sink when wearing skis.
A skier of $60\ \text{kg}$ is standing on the snow. Take $g = 10\ \text{m/s}^2$. a) Calculate her weight. b) Wearing boots, she rests on two soles of…
A skier of $60\ \text{kg}$ is standing on the snow. Take $g = 10\ \text{m/s}^2$.
- a) Calculate her weight.
- b) Wearing boots, she rests on two soles of $25\ \text{cm} \times 10\ \text{cm}$ each. Calculate the pressure she exerts on the snow (take care with unit conversions).
- c) Wearing skis, she rests on two skis of $1.5\ \text{m} \times 0.2\ \text{m}$ each. Calculate the pressure now.
- d) Compare the two results and explain why she does not sink when wearing skis.
Compare the following two situations, shown in the figure. Take $g = 10\ \text{m/s}^2$. a) A $55\ \text{kg}$ person rests all their weight on two stiletto heels of…
Compare the following two situations, shown in the figure. Take $g = 10\ \text{m/s}^2$.
- a) A $55\ \text{kg}$ person rests all their weight on two stiletto heels of $1\ \text{cm}^2$ each: calculate the pressure exerted on the ground (take care with unit conversions).
- b) A $5\,000\ \text{kg}$ elephant rests on its four feet, of $0.1\ \text{m}^2$ each: calculate the pressure it exerts.
- c) Who exerts more pressure on the ground? Compare the results and explain the role played by the contact area.
Pressure inside a liquid
If you poke holes in a plastic bottle of water at three different heights, the stream from the lowest hole comes out with more force and travels farther. The water is the same. Why does it push harder at the bottom?
Because at the bottom there is more water on top. A liquid at rest exerts pressure because of its own weight, and that pressure depends on the depth.
Notice what the formula says: the pressure grows in proportion to the depth (twice as deep, twice the pressure) and to the density of the liquid. The volume and the shape of the container do not appear.
A swimming pool is $2\ \text{m}$ deep, as shown in the figure. Given: $d_{agua} = 1\,000\ \text{kg/m}^3$; take $g = 10\ \text{m/s}^2$. Calculate the pressure exerted by…
A swimming pool is $2\ \text{m}$ deep, as shown in the figure. Given: $d_{agua} = 1\,000\ \text{kg/m}^3$; take $g = 10\ \text{m/s}^2$.
Calculate the pressure exerted by the water on the bottom using $p = d\times g\times h$.
When swimming down to the bottom of a pool, you feel pressure in your ears, and the deeper you go, the more uncomfortable it becomes. Explain which quantity is changing…
When swimming down to the bottom of a pool, you feel pressure in your ears, and the deeper you go, the more uncomfortable it becomes. Explain which quantity is changing with depth and why.
A dam holds back water in a reservoir that reaches a depth of $30\ \text{m}$ next to the wall, as shown in the figure. Data: $d_{agua} = 1\,000\ \text{kg/m}^3$; take…
A dam holds back water in a reservoir that reaches a depth of $30\ \text{m}$ next to the wall, as shown in the figure. Data: $d_{agua} = 1\,000\ \text{kg/m}^3$; take $g = 10\ \text{m/s}^2$.
- a) What pressure does the water exert on the base of the dam?
- b) A small sluice gate at the bottom has a surface area of $2\ \text{m}^2$; assume that the whole gate is subject to the pressure found in part a). With what force does the water push against that sluice gate?
Applying hydrostatic pressure
This formula explains why water tanks are placed on rooftops: the higher the water level is above the faucet, the greater the pressure with which it comes out. It also explains why dams are thicker at the base than at the top.
The water tank of a housing estate is at the top of a tower, $12\ \text{m}$ above the tap of a house, as shown in the figure. Given: $d_{agua} = 1\,000\ \text{kg/m}^3$;…
The water tank of a housing estate is at the top of a tower, $12\ \text{m}$ above the tap of a house, as shown in the figure. Given: $d_{agua} = 1\,000\ \text{kg/m}^3$; take $g = 9.8\ \text{m/s}^2$.
- a) Calculate the pressure due to the column of water reaching the tap.
- b) What will that pressure be at the tap on the ground floor, located $3\ \text{m}$ lower down?
A dam holds back water in a reservoir with a maximum depth of $40\ \text{m}$ next to the wall, as shown in the figure. Data: $d_{agua} = 1\,000\ \text{kg/m}^3$; take…
A dam holds back water in a reservoir with a maximum depth of $40\ \text{m}$ next to the wall, as shown in the figure. Data: $d_{agua} = 1\,000\ \text{kg/m}^3$; take $g = 10\ \text{m/s}^2$.
- a) What pressure does the wall withstand at its base?
- b) What about at a depth of $10\ \text{m}$?
- c) With those two results, explain why dams are built much thicker at their base than at the top.
A building's water tank is on the roof, $15\ \text{m}$ above a faucet on the second floor. Data: $d_{agua} = 1\,000\ \text{kg/m}^3$; take $g = 9.8\ \text{m/s}^2$. a)…
A building's water tank is on the roof, $15\ \text{m}$ above a faucet on the second floor. Data: $d_{agua} = 1\,000\ \text{kg/m}^3$; take $g = 9.8\ \text{m/s}^2$.
- a) Calculate the water pressure at that faucet.
- b) When closed, the faucet has a cross-sectional area of $1\ \text{cm}^2$: with what force does the water push against it?
- c) A neighbor on the ground floor has their faucet $9\ \text{m}$ lower down: calculate the pressure at their faucet and explain the difference compared to the second floor.
Atmospheric pressure
Atmospheric pressure decreases with altitude, because the higher up you are, the less air is left above you. In Mexico City (at about $2{,}240\ \text{m}$) it is noticeably lower than in Veracruz, next to the sea.
What is atmospheric pressure? Name the instrument used to measure it and write down its approximate value at sea level, in pascals.
What is atmospheric pressure? Name the instrument used to measure it and write down its approximate value at sea level, in pascals.
On the weather map, a low-pressure system has a pressure at its center of $990\ \text{hPa}$ and a high-pressure system, of $1\,030\ \text{hPa}$. a) Express both…
On the weather map, a low-pressure system has a pressure at its center of $990\ \text{hPa}$ and a high-pressure system, of $1\,030\ \text{hPa}$.
- a) Express both pressures in pascals (remember: $1\ \text{hPa} = 100\ \text{Pa}$).
- b) The normal value of atmospheric pressure at sea level is $1\,013\ \text{hPa}$: which of the two systems is closer to that value?
- c) Given that depressions usually bring clouds and rain and anticyclones bring settled weather, indicate in which of the two you would expect bad weather and give reasons for your answer.
In Torricelli's experiment, a glass tube is filled with mercury and inverted over a trough containing mercury: the column falls until it reaches a height of…
In Torricelli's experiment, a glass tube is filled with mercury and inverted over a trough containing mercury: the column falls until it reaches a height of $76\ \text{cm}$ above the surface of the trough, as shown in the figure. Data: $d_{Hg} = 13\,600\ \text{kg/m}^3$; take $g = 9.8\ \text{m/s}^2$.
- a) Calculate the pressure exerted by this mercury column on its base.
- b) Compare the result with the value of atmospheric pressure at sea level and explain what the experiment demonstrates and what is at the top of the tube.
- c) What height should the column be if the experiment were carried out with water instead of mercury?
Total pressure underwater
When an object is inside a liquid that is open to the air, it is not only squeezed by the water: it is also squeezed by the air pushing on the free surface.
A scuba diver dives at a depth of $10\ \text{m}$ in a lake, as shown in the figure. Data: $d_{agua} = 1\,000\ \text{kg/m}^3$, $p_{atm} = 101\,300\ \text{Pa}$; take…
A scuba diver dives at a depth of $10\ \text{m}$ in a lake, as shown in the figure. Data: $d_{agua} = 1\,000\ \text{kg/m}^3$, $p_{atm} = 101\,300\ \text{Pa}$; take $g = 10\ \text{m/s}^2$.
- a) Calculate the pressure due solely to the water above him.
- b) Calculate the total pressure he experiences, adding atmospheric pressure.
- c) How many times atmospheric pressure is that total pressure? Comment on the result.
A scuba diver descends to a depth of $20\ \text{m}$ in the sea. Data: $d_{mar} = 1\,025\ \text{kg/m}^3$, $p_{atm} = 101\,300\ \text{Pa}$; take $g = 10\ \text{m/s}^2$. a)…
A scuba diver descends to a depth of $20\ \text{m}$ in the sea. Data: $d_{mar} = 1\,025\ \text{kg/m}^3$, $p_{atm} = 101\,300\ \text{Pa}$; take $g = 10\ \text{m/s}^2$.
- a) Calculate the pressure exerted by the water at that depth.
- b) Calculate the total pressure experienced by the diver, adding atmospheric pressure.
- c) How many times the atmospheric pressure is this total pressure?
- d) Using the previous result, explain why divers must plan their dives and control their ascent.
Atmospheric pressure in action
The atmosphere pushes with enormous force: $F = p\times S$. On a sheet of paper of $0.06\ \text{m}^2$ (roughly letter size) the force of the air is almost $6{,}000\ \text{N}$. We don't notice it because the air also pushes from below and from all sides, and the forces cancel out.
When the pressures on the two sides of a surface are not equal, a net force appears:
$$F_{net} = (p_{higher} - p_{lower}) \times S$$The atmosphere pushes down on your tabletop with a pressure of about $101\,300\ \text{Pa}$. The tabletop measures $1.2\ \text{m} \times 0.6\ \text{m}$. a) Calculate the…
The atmosphere pushes down on your tabletop with a pressure of about $101\,300\ \text{Pa}$. The tabletop measures $1.2\ \text{m} \times 0.6\ \text{m}$.
- a) Calculate the surface area of the tabletop.
- b) Calculate the force with which the atmosphere crushes it.
- c) If the force is so huge, why does the table not break or collapse? Think about the air underneath the tabletop.
A mountaineer climbs Mulhacén ($3\,479\ \text{m}$) and their barometer reads $670\ \text{hPa}$; before setting off, at sea level, it read $1\,013\ \text{hPa}$. a)…
A mountaineer climbs Mulhacén ($3\,479\ \text{m}$) and their barometer reads $670\ \text{hPa}$; before setting off, at sea level, it read $1\,013\ \text{hPa}$.
- a) Express both pressures in pascals.
- b) What percentage of the sea-level pressure remains at the summit?
- c) Explain why atmospheric pressure decreases with altitude (think about how much air remains above you) and explain why water boils below $100\ \celsius$ at the summit.
In a classic laboratory experiment, a metal can containing a little water is heated until it boils and is quickly sealed; on cooling, the can crushes itself without…
In a classic laboratory experiment, a metal can containing a little water is heated until it boils and is quickly sealed; on cooling, the can crushes itself without anyone touching it. The figure outlines the interior and exterior pressures on the walls of the can.
- a) Explain what happens to the water vapour inside on cooling, and what then happens to the pressure inside the can.
- b) If at a given moment the interior pressure is $40\,000\ \text{Pa}$ and the exterior pressure is $100\,000\ \text{Pa}$, calculate the pressure difference between both sides of the walls.
- c) Calculate the net force crushing the can if the exposed surface area is $0.04\ \text{m}^2$, and explain why it buckles inwards rather than outwards.
Back to the beginning: if you push with $30\ \text{N}$, your flat finger ($S \approx 1.5\ \text{cm}^2 = 1.5\times 10^{-4}\ \text{m}^2$) exerts $200{,}000\ \text{Pa}$. The tip of the thumbtack ($S \approx 0.1\ \text{mm}^2 = 10^{-7}\ \text{m}^2$) concentrates the same force and exerts $300{,}000{,}000\ \text{Pa}$: fifteen hundred times more pressure with the same effort.